how to light a gas fireplace

You will need to hold your pilot button for the allotted time that your owners manual suggests. A standing pilot light can prevent small silky spider webs from forming inside the fireplace that may result in a service call to get the fireplace back in service.

Starting A Gas Fireplace A How To About Your Owner S Manual Pilot Lights Your Enjoyment Chimneys Plus

The pilot position is commonly found as a setting on a control dial as is with our gas fireplace.

. Most of them are made of glass so be careful how you put them down. Push in the pilot knob which will then manually send gas into the system. You should hear a whoosh noise as it lights and you should be able to see a little blue flame in the burner.

Turn the gas knob counter-clockwise to pilot. The pilot position is typically set on the control dial with either the dial depressed and turned or used with a separate spark button to light the pilot flame. The steps involved in lighting your pilot on your gas fireplace include.

You can do this by turning the knob to the Pilot position. This video will show you how to light a gas fireplace with a piezo spark ignitor. Press and continue to press down on the control knob while UD press the ignition switch one time per second.

Switch the pilot switch to the on setting. Though most fireplaces use similar methods. Once the pilot is lit cease from pressing the ignition switch.

Depress slightly and hold the gas knob while lighting the pilot with the igniter push button keep knob depressed and after some seconds release it if the pilot doesnt continue to burn and repeat all the above steps. Read and follow the instructions that came with you. Removal of the Gas Fireplaces Cover The first step that you need to take to light your pilot is to remove the cover on your fireplace to reveal the controls.

Depending on how long its been since the gas fireplace was last used ignition may take several attempts before igniting. Turn the OffPilotOn knob to the Pilot position. My pilot light will not stay lit gas fireplace gas.

Lighting A Gas Fireplace Using A Key There are some gas fireplaces that use a metal key to start the flames and gas flow follow the steps below if you have one. The pilot light will remain on to allow you to do this. Click the piezoelectric igniter a few times until the pilot lights.

The next very important step in how to light a gas fireplace is to light the pilot light. Once this is done you will now be able to easily switch your gas fireplace on or off using either a remote control device or a switch on the wall. Press this button and you should see the pilot light turn on whenever you turn the gas control to start the gas.

Before you light up that fireplace make sure to read the included manual thoroughly. Push in the gas valve Start button while lighting the pilot with a match or lighting device. With the pilot lit turn the gas knob counter-clockwise to on position.

Turn the control knob to the on position. Turn Control Gas Valve Knob to OFF. While in the ignite position press down on the knob until you begin to hear a clicking sound.

Remove the outer cover so you can ignite the pilot light. Push the igniter button once every second until it lights. Most fireplaces unless specified otherwise in the manual have a gas control knob which is next to a colored button.

Hold the valve in the light position for 30 seconds until you see a flame. Push in the pilot knob which manually sends gas into the system. Locate the pilot light which could be behind a panel or under the main frame of the unit.

Take a lighter with a head long enough such that you can light the fire pit while keeping your hands at a safe distance. Turn the pilot to the Light middle position. How do you light a gas fireplace.

Push the igniter button once every second until it lights. Light A Gas Fireplace With A Control Panel. Intermittent pilot ignition ipi mode means that the pilot light will light and extinguish each time the unit is used the ignition system will first ignite the pilot light before opening the gas valve to the main.

The manual controls for a gas fireplaces will typically have a Pilot position that that allows the pilot light to be started. Replacement piezo ignitor httpamznto2i7clAn Replacement Thermopile httpamznto2j1sFm3WARNING. The first think you want to do is pull the cover off the fireplace.

Turn the control to the On position How to light a Gas Fireplace with an electronic ignition starting system. Most gas fireplaces have a standing pilot light which is a small flame that burns even when you arent using your fireplace. Keep pushing the button until the pilot light turns on.

The pilot position on the control dial for our gas fireplace. You can turn up the gas at this point since the pilot is. The fire should be lit.

Bring the lighter near the fireplace and move the gas valve key in a counterclockwise direction. Depending on how long its been since the gas fireplace was last used ignition may take multiple attempts. Press and hold down the gas control knob then press the igniter button multiple times as needed until the pilot flame ignites.

A flashlight is handy for finding this small but important dial. Ignite it and get away quickly from the fire pit. Hold the knob in for at least 30 seconds.

Light a match near the fires piping while holding down the pilot lighter. How To Light A Gas Fireplace. Gas fireplaces with electronic ignition will typically have a way to light it in the form of a wall switch andor a remote control.

Push in the pilot knob which will then manually send gas into the system. Spark That Fire Bring on the heat by first approaching the gas valve and making sure it is on. These should be toward the bottom of the unit and they include a shut-off valve for the gas.

First turn your gas fireplaces knob from the Off to the Pilot position. Ensure that the valve is properly aligned with the gas line of your fireplace for ultimate control of the flow of the fuel. Simply pressing the wall switch or correct button on a remote control can light a gas fireplace with electronic ignition in an instant.

Press and Hold the knob in. Once the pilot lights keep holding down the gas control knob for 20 to 30 seconds to allow time for heating up the thermocouple a safety device then release the knob so it pops back up. Turn the knob from the Off to the Pilot position.

Wear safety gloves if you are new to operating a fireplace.

Gas Fireplace Won T Stay Lit Magic Touch Mechanical